**Welcome to the official ADCIRCWiki site! The site is currently under construction, with limited information. ---**

# Generalized Asymmetric Holland Model

The Generalized Asymmetric Holland Model (GAHM) is a parametric hurricane vortex model developed in ADCIRC for operational forecasting purpose. Based on the classic Holland Model, the GAHM removes the assumption of cyclostrophic balance at the radius of maximum wind, and allows for a better representation of a wide range of hurricanes. Another important feature of the GAHM is the introduction of a composite wind method, which when activated enables the usage of multiple storm isotaches in reconstructing the spatial pressure and wind fields, while only one isotach is used in the HM.

## Contents

## The Classic Holland Model

The Holland Model (HM, 1980) is an analytic model that describes the radial pressure and wind profiles of a standard hurricane. To begin with, Holland found that the normalized pressure profiles of a number of hurricanes resemble a family of rectangular hyperbolas and may be approximated by a hyperbolic equation, which after antilogarithms and rearranging yields the radial pressure equation:

where is the central pressure, is the ambient pressure (theoretically at infinite radius), is the pressure at radius from the center of the hurricane, and and are shape parameters that may be empirically estimated from observations in a hurricane.

Substituting (1) into the gradient wind equation, which describes a steady flow balanced by the horizontal pressure gradient force, the centripetal acceleration, and the Coriolis acceleration for a vortex above the influence of the planetary boundary layer where the atmospheric flow decouples from surface friction (Powell et al. 2009), gives the radial wind equation of a hurricane:

where is the gradient wind at radius , is the density of air, is the Coriolis parameter. In the region of the maximum winds, if we assume that the Coriolis force is negligible in comparison to the pressure gradient and centripetal force, then the air is in cyclostrophic balance. By removing the Coriolis term in (2) we get the cyclostrophic wind

By setting at radius to the maximum wind , it is obtained that

Thus the () is irrelevant to the relative value of ambient and central pressures, and is solely defined by the shape parameters and . Substituting (4) back into (3) to get rid of , we get an estimate of as a function of the maximum wind speed

It was notable that the maximum wind speed is proportional to the square root of and irrespective of the (), given a constant pressure drop. It was also reasoned by Holland that a plausible range of would be between 1 and 2.5 for realistic hurricanes. Substituting (4) and (5) back into (1) and (2) yields the final radial pressure and wind profiles for the HM

The HM was implemented in the ADICRC as a wind module with NWS = 19. When sparse observations of a hurricane are given, estimates of the and shape parameter may be estimated by fitting data into the radial wind equation, which in turn allow us to compute and along the radius of the hurricane. However, discrepancies between wind observations and computed winds were sometimes found, and were negatively correlated to the Rossby number at , defined as

By definition, a large describes a system in cyclostrophic balance that is dominated by the inertial and centrifugal force with negligible Coriolis force, such as a tornado or the inner core of an intense hurricane, whereas a small value signifies a system in geostrophic balance where the Coriolis force plays an important role, such as the outer region of a hurricane. As a result, the assumption of cyclostrophic balance at made in HM is mostly valid for describing an intense and narrow (small ) hurricane with a large , but not applicable for a weak and broad hurricane with a small . This intrinsic problem with the HM calls our intention to develop a generalized model that will work consistently for a wide range of hurricanes, which theoretically can be accomplished by removing the above cyclostrophic balance assumption and re-derive the radial pressure and wind equations (6)&(7).

## Derivation of the GAHM

The GAHM also starts with the same radial pressure and wind equations (1)&(2) with shape parameters and as in the HM. Without assuming cyclostrophic balance at , we take at to get the adjusted shape parameter as

where is a scaling parameter introduced to simplify the derivation process, defined as

and later derived as

Thus, the in the GAHM is not entirely defined by the shape parameters and as in the HM, but also by the scaling factor , as Equation (11) indicates that . Numerical solutions for and can be solved iteratively in the model using Equation (9)&(11). Figure 1 illustrates how and vary with given different values. It is evident that values of both and remain close to 1 when is within the range of [1,2], but increase noticeably as decreases below 1, and the smaller the value of , the bigger the changes.

Substituting (9)&(11) back into (1)&(2) yields the final radial pressure and wind equations for the GAHM

Influence of the Coriolis force on the radial pressure and wind profiles are evidenced by the presence of and in (12)&(13). A special case scenario is when we set , which corresponds to an infinitely large , then (12)&(13) in the GAHM reduce to (6)&(7) in the HM. However，for a hurricane with a relatively small , the influence of the Coriolis force can only be addressed by the GAHM. It meets our expectation that the GAHM’s solution approaches to that of the HM’s when the influence of Coriolis force is small, but departs from it when the Coriolis force plays an important role in the wind system.

The above reasoning can be demonstrated by the 3D plots in Figure 2, which show the normalized gradient winds of the HM (left panel) and the GAHM (right panel) as functions of the normalized radial distances , the Holland parameter, and . In both panels, each colored surface represents the normalized gradient winds corresponding to a unique Holland B value. By definition, we get at , which means all the surfaces in each panel should intersect with the plane of on the plane of , no matter what values of . However, the line of intersection (shown by the black line) shown in the left panel deviates from the plane of as decreases from 2 to close to 0 ( decreases from 100 to 1), while remains on the plane regardless of how changes in the right panel, demonstrating that the GAHM is mathematically more coherent than the HM.

To have a dissective look of the surface plots in Figure 2, we draw slices perpendicular to the axis of at three different values 0, 1, 2, and plot the lines of intersection with each surface in Figure 3. It is evident that we get at consistently in the right panel for the GAHM regardless of the value of . The HM in the left panel, however, generates distorted wind profiles with underestimated maximum winds skewed inward towards the storm center, espeically when . As a results, when both models being applied to real hurricane cases, the GAHM will perform more consistently than the HM.

## Calculation of the Radius to the Maximum Wind

Both the HM and the GAHM use processed forecast advisories (during active hurricanes) or best track advisories (post-hurricanes) from the National Hurricane Center (NHC) in ATCF format as input files, which contain a time series of storm parameters (usually at 6-hour intervals) such as storm location, storm movement, central pressure, 1 minute averaged maximum wind, radii to the 34-, 50-, and/or 64-kt storm isotaches in 4 storm quadrants (NE, SE, SW, NW), etc. See meteorological input file with NWS = 20 for more details.

As a standard procedure, for all data entries in the input file the and are pre-computed in 4 storm quadrants of all available isotaches in the ASWIP program (an external FORTRAN program developed by Flemming et al. and further developed here to accommodate the GAHM) and appended to the input file prior to running an ADCIRC simulation forced with the GAHM wind model.

First, the influence of the boundary layer effect must be removed to bring the maximum sustained wind and the 34-, 50-, and/or 64-kt isotaches from 10 meter height to the gradient wind level. Practically, the maximum gradient wind can be directly calculated as

where is the reported maximum sustained wind at 10 meter height assuming in the same direction as , is the storm translational speed calculated from successive storm center locations, is the wind reduction factor for reducing wind speed from the gradient wind level to the surface at 10 meter height (Powell et al., 2003), and is the damp factor for . The following formula of is employ in the ASWIP program:

which is the ratio of gradient wind speed to the maximum wind speed along a radial wind profile. Thus, is zero at storm center, and increases with until reaches a maximum value of 1 at , then gradually decreases outward to zero.

In addition to the scalar reduction in wind speed, surface friction and continuity also cause the vortex wind to flow inward across isobars, with an inward rotation angle according to the Queensland Government's Ocean Hazards Assessment (2001):

Thus, the gradient wind at the radii to specified storm isotaches in 4 storm quadrants can be obtained from the observed isotaches as

where is the observed isotach wind speed with an unknown angle , and is the wind speed at radius to specified isotach before the inward rotation angle is removed.

Rewriting (17) in x- and y-components yields:

where is the azimuth angle of the storm quadrant (NE, SE, SW, NW at , respectively), and are the zonal and meridional components of , and are the zonal and meridional components of .

Given an initial guess of , values of and can be solved iteratively from (9) and (11) until both converge, and can be estimated by combining (15), (17), (18), and (19). Plugging from (14), the above calculated and the observed radius to back into (13), a new can be inversely solved by a root-finding algorithm. Since the above calculations are carried out based on an initial guess of , wWe need to repeat the entire process until converges.

In case where multiple isotaches are given in the forecast/best track advisories, the for the highest isotach will be calculated using the above procedure, and used as the pseudo for the entire storm (physically, there is only one found along a radial wind profile ). For each lower isotach, will be calculated with the pseudo set as its initial value to determine the inward rotation angle following the above process only once. The use of the pseudo across all storm isotaches ensures that the cross-isobar frictional inflow angle changes smoothly along the radius according to (17).

Occasionally, we have to deal with situations where , which violate (13) so couldn't be calculated. These situations mostly happen in the right hand quadrants (in the Northern Atmosphere) of a weak storm with a relatively high translational speed. For cases like this, we assign , which is equivalent to assigning .

After the ASWIP program finishes processing the input file, it can be readily used by the GAHM to construct spatial pressure and wind fields in ADCIRC for storm surge forecast.

## Composite Wind Generation

Since storm parameters are only given in 4 storm quadrants (assuming at azimuthal angles, respectively) at 3 available isotaches in the input file, spatial interpolation of storm parameters must take place first at each ADCIRC grid node. Traditionally, the single-isotach approach is used, in which storm parameters will be interpolated azimuthally from the highest isotach only. To take advantage of the availability of multiple isotaches, a new composite wind method is introduced in the GAHM, the multiple-isotach approach, in which storm parameters will be interpolated both azimuthally and radially from all available isotaches.

To begin, the relative location of a node to the storm center at given time is calculated, specified by the azimuth angle and distance . The angle places the node between two adjacent quadrants and , where . For each storm parameter to be interpolated, its value at are weighted between its values at two pseudo nodes and :

The distance then places each pseudo node between the radii of two adjacent isotaches in its quadrant, and the value at the pseudo node is interpolated using the inverse distance weighting (IDW) method:

where are parameter values computed from the 34-, 50-, and 64-isotach, are distance weighting factors for each isotach, calculated as

and .

The above procedure is performed at each node of an ADCIRC grid. After all storm parameters are interpolated, the pressure and gradient winds can be calculated using (12)&(13). To bring the gradient wind down to the standard 10 meter reference level, the same wind reduction factor is applied, and the tangential winds are rotated by an inward flow angle β according to (16). Then, the storm translational speed is added back to the vortex winds. Last but not least, a wind averaging factor is applied to convert resulted wind field from 1-min to 10-min averaged winds in order to be used by ADCIRC. This new composite wind method is simple and efficient, and more importantly, it assures that the constructed surface winds match all observed storm isotaches provided in NHC’s forecast or “best track” advisories.

## Case Studies

Preliminary evaluation of the GAHM was carried out based on seven hurricanes that struck the Gulf of Mexico and the Eastern United States: Katrina (2005), Rita (2005), Gustav (2008), Ike (2008), Irene (2011), Isaac (2012), and Sandy (2012), see Table 1. Ranging from category 1 to 5 on the Saffir-Simpson Hurricane Wind Scale, these storms vary in storm track, forward motion, size, intensity, and duration, but all caused severe damages to coastal states due to destructive winds, wind-induced storm surges, and ocean waves. Their “best track” advisories were retrieved from NHC’s ftp site (ftp://ftp.nhc.noaa.gov/atcf; previous years’ data are located in the archive directory) and pre-processed using the ASWIP program. The “best track” file contains an estimate of the radius to the maximum wind for each data entry, but will solely be used for model validation purpose as both the GAHM and HM calculate their own spatially-varying .

Hurricane | Saffir-Simpson Wind Scale | Maximum Sustained Wind (knot) | Minimum Central Pressure (mbar) | Period from Formation to Dissipation |
---|---|---|---|---|

Katrina |
5 | 150 | 902 | 08/23-08/30, 2005 |

Rita |
5 | 150 | 902 | 09/18-09/26, 2005 |

Gustav |
4 | 135 | 941 | 08/23-09/04, 2008 |

Ike |
4 | 125 | 935 | 09/01-09/14, 2008 |

Irene |
3 | 105 | 942 | 08/21-08/30, 2011 |

Isaac |
1 | 70 | 965 | 08/21-09/03, 2012 |

Sandy |
3 | 95 | 940 | 10/22-10/01, 2012 |

Besides the maximum wind speed, both Holland and can be used as key parameters to characterize the development of the storm. Figure 4 depicts the change of , , and during different stages of the hurricanes along their best tracks. Typically, both and increase as hurricane strengthens, and decrease as hurricane dissipates, within range of (0, 2.5). Previously via analytical evaluation we have demonstrated that the GAHM behaves consistently better than the HM, especially under situations where . Here, evaluation of model performance will be carried out by comparing the modeled winds with the observed winds in the "best track" data, as well as the SLOSH (Sea, Lake, and Overland Surges from Hurricanes) winds, re-analysis H*Wind and hindcast OWI winds.

Figure 4. The development of (a) The Maximum Wind Speed, (b) Holland , and (c) along the best tracks of 7 selected hurricanes |