**Welcome to the official ADCIRCWiki site! The site is currently under construction, with limited information. ---**

# Difference between revisions of "Manning's n at sea floor"

(→Negative n Values) |
|||

(5 intermediate revisions by the same user not shown) | |||

Line 4: | Line 4: | ||

[[File:mnasfContours3.png|400px|right|thumb|Drag coefficient <math>C_d</math> contours for Manning's n and total depth]] | [[File:mnasfContours3.png|400px|right|thumb|Drag coefficient <math>C_d</math> contours for Manning's n and total depth]] | ||

If the user elects to use this nodal attribute, which ADCIRC reads in as the <code>[[ManningsN]]</code> variable, <code>[[NOLIBF]]</code> must be set to 1 or the run will terminate. During execution, the Manning’s n values specified are converted to equivalent quadratic friction coefficients before the bottom stress is calculated. The equivalent quadratic friction coefficient is calculated according to the following formula at each node at each time step: | If the user elects to use this nodal attribute, which ADCIRC reads in as the <code>[[ManningsN]]</code> variable, <code>[[NOLIBF]]</code> must be set to 1 or the run will terminate. During execution, the Manning’s n values specified are converted to equivalent quadratic friction coefficients before the bottom stress is calculated. The equivalent quadratic friction coefficient is calculated according to the following formula at each node at each time step: | ||

− | :<math> | + | :<math>C_d(t)=\frac{gn^2}{\sqrt[3]{h+\eta(t)}}</math> |

where, | where, | ||

− | * ''C''<sub>'' | + | * ''C''<sub>''d''</sub> drag coefficient |

* ''t'' time | * ''t'' time | ||

* ''g'' acceleration due to gravity | * ''g'' acceleration due to gravity | ||

Line 16: | Line 16: | ||

== Negative ''n'' Values == | == Negative ''n'' Values == | ||

− | If a combination of Manning's and time invariant [[bottom friction]] is desired, users can elect to set the Manning's [[nodal attribute]] to a negative value at certain mesh nodes. At mesh nodes where ''n'' is negative, the time invariant ''C''<sub>'' | + | {{ADC version|version=55|relation=ge}} |

+ | If a combination of Manning's and time invariant [[bottom friction]] is desired, users can elect to set the Manning's [[nodal attribute]] to a negative value at certain mesh nodes. At mesh nodes where ''n'' is negative, the time invariant ''C''<sub>''d''</sub> coefficient, specified via a constant <code>[[CF]]</code> in the [[fort.15 file]] or the spatially varying [[Fort.13_file#Quadratic_Friction_coefficient|quadratic_friction_coefficient_at_sea_floor]] fort.13 nodal attribute, will be used instead. | ||

== Specifying ''n'' Values == | == Specifying ''n'' Values == |

## Latest revision as of 01:08, 14 April 2020

The ** mannings_n_at_sea_floor** nodal attribute is one of the available options for specifying bottom friction in ADCIRC based on the Manning formula. It is a nodal attribute in the fort.13 file, meaning that it allows spatially (and temporally) varying bottom friction in the model.

## Attribute Summary

If the user elects to use this nodal attribute, which ADCIRC reads in as the `ManningsN`

variable, `NOLIBF`

must be set to 1 or the run will terminate. During execution, the Manning’s n values specified are converted to equivalent quadratic friction coefficients before the bottom stress is calculated. The equivalent quadratic friction coefficient is calculated according to the following formula at each node at each time step:

where,

*C*_{d}drag coefficient*t*time*g*acceleration due to gravity*n*Manning's n*h*depth*η*water surface elevation

The addition of the water surface elevation is conditional upon the setting of `NOLIFA`

: *η* is treated as zero if `NOLIFA = 0`

in the fort.15 file. Finally, the value of `CF`

in the fort.15 is used to set a lower limit on the resulting equivalent quadratic friction coefficient, under the assumption the *C*_{d} calculated from this formula tends to become too small in deep water.

## Negative *n* Values

ADCIRC version: | ≥ 55 |

If a combination of Manning's and time invariant bottom friction is desired, users can elect to set the Manning's nodal attribute to a negative value at certain mesh nodes. At mesh nodes where *n* is negative, the time invariant *C*_{d} coefficient, specified via a constant `CF`

in the fort.15 file or the spatially varying quadratic_friction_coefficient_at_sea_floor fort.13 nodal attribute, will be used instead.

## Specifying *n* Values

Manning's *n* is often assigned using land cover datasets, when available. Examples of commonly used land cover data in the US are the National Land Cover Dataset and the Coastal Change Analysis Program. There is a broad literature on specification of *n* values based on laboratory and fields studies, the most classical example of which is Chow (1959). Ideally, field surveys or review of on-site photography should be done to correlate land cover values to *n*. Alternatively, review of available literature may provide some basis for selecting values.